PRODUCTS
Steel Wire Electro Galvanizing Line – Continuous Zinc Plating Production Line
- Process: Continuous electrolytic zinc plating (steel wire electro galvanizing line)
- Wire diameter: Ø0.76–3.2 mm
- Wires per line: 42 / 48 / 56 (models DDX42, DDX48, DDX56)
- Coating weight: 20–60 g/m², adjustable by current density and line speed
- Wire material: Low-, medium- and high-carbon steel wire (for example Q195, Q235)
- Tensile strength range: 300–1,300 MPa
- Heat treatment furnace: Up to 1,100 °C, natural gas or LPG fired
- Design DV (diameter × speed) : 80 mm·m/min
- Take-up: Inverted (headstand) coil or spool take-up
- Power supply: 380 V / 50 Hz, or customized to your grid
Steel Wire Electro Galvanizing Line – Continuous Zinc Plating Production Line
The YF Metal Tech steel wire electro galvanizing line is a continuous, multi-wire production line that cleans, plates and passivates steel wire in one pass. It processes wire from Ø0.76 mm to Ø3.2 mm, runs up to 56 wires at the same time, and deposits a bright, uniform zinc layer of 20–60 g/m² (customizable). It is designed for wire makers who supply wire mesh, hardware, fasteners, appliance parts and packaging wire, where surface finish and coating control matter more than the very heavy zinc weights of hot-dip lines.
We design and manufacture the line, and we can configure it with or without online annealing, to your wire grade, capacity and plant layout.
Key Specifications
|
Item |
Standard configuration |
|---|---|
| Process | Continuous electrolytic zinc plating (electro galvanizing) |
| Wire diameter | Ø0.76–3.2 mm |
| Wires per line | 42 / 48 / 56 (models DDX42, DDX48, DDX56) |
| Coating weight | 20–60 g/m², adjustable by current density and line speed |
| Wire material | Low-, medium- and high-carbon steel wire (for example Q195, Q235) |
| Tensile strength range | 300–1,300 MPa |
| Heat treatment furnace | Up to 1,100 °C, natural gas or LPG fired |
| Design DV (diameter × speed) | 80 mm·m/min |
| Take-up | Inverted (headstand) coil or spool take-up |
| Power supply | 380 V / 50 Hz, or customized to your grid |
| Control | PLC, automatic / semi-automatic / manual modes |
| Customization | Wire count, capacity, layout, annealing, coating type, take-up |
How the Electro Galvanizing Line Works: Process Flow
A typical steel wire electro galvanizing line follows this sequence. Each stage can be adjusted to the wire grade and the finish you need.
Process Flow of Electro Galvanizing Production Line: Pay off wires → degreasing bath → heat treatment furnace → water quench → water cooling → HCL pickling bath → water rinse → electro galvanizing → water rinsing → passivation → hot water wash → drying → take up
- Pay-off. Coils are loaded and uncoiled with automatic centering and stable tension for every wire.
- Degreasing bath. Removes drawing lubricant and oil so later stages work evenly.
- Heat treatment furnace (optional online annealing). Restores ductility after drawing. The furnace runs up to 1,100 °C on natural gas or LPG.
- Water quench and water cooling. Cools the wire in a controlled way. The water-patenting length is adjustable from 200 to 6,500 mm.
- HCl pickling. Removes oxide scale and leaves a chemically clean surface.
- Water rinse. Stops acid carry-over into the plating tank.
- Electro galvanizing. Wire passes through the plating tank as the cathode while zinc is deposited from the electrolyte. Coating weight is set by current and residence time.
- Water rinse.
- Passivation. Improves white-rust resistance and handling life. Phosphate, chromate or organic post-treatments are available on request.
- Hot water wash.
- Hot-air drying.
- Take-up. Constant-tension winding into inverted coils or onto spools.
Why Zinc Coating Weight Matters?
Electro galvanized zinc is thin by design. As a reference, 1 g/m² of zinc is about 0.14 µm thick, so 20–60 g/m² corresponds to roughly 3–8 µm. On a Ø2.0 mm wire, that is only about 0.5–1.5% zinc by weight. This is why electro galvanized wire has a bright, smooth surface and keeps good ductility for weaving, bending and forming, while hot-dip wire carries heavier zinc for long outdoor life.
Steel Wire Electro Galvanizing Line Model Parameters (DDX series)
|
Parameter |
DDX42 | DDX48 |
DDX56 |
|---|---|---|---|
| Steel wire diameter | Ø0.76–3.2 mm | Ø0.76–3.2 mm | Ø0.76–3.2 mm |
| Number of wires | 42 | 48 | 56 |
| Coating weight | 20–60 g/m² | 20–60 g/m² | 20–60 g/m² |
| Furnace max. temperature | 1,100 °C | 1,100 °C | 1,100 °C |
| Furnace fuel | NG / LPG | NG / LPG | NG / LPG |
| Design DV | 80 mm·m/min | 80 mm·m/min | 80 mm·m/min |
| Water patenting adjustment | 200–6,500 mm | 200–6,500 mm | 200–6,500 mm |
| Max. plating current | Customized | Customized | Customized |
| Take-up | Inverted coil / spool | Inverted coil / spool | Inverted coil / spool |
| Theoretical output at Ø2.0 mm* | about 2.5 t/h | about 2.8 t/h | about 3.3 t/h |
*Theoretical maximum from the design DV (80 mm·m/min ÷ 2.0 mm = 40 m/min per wire, about 59 kg/h per wire) at continuous running. Real output depends on plating residence time, coating weight, uptime and wire grade, and is confirmed in your quotation. All models can be customized.
Key Features and Advantages
- Intelligent electrode shaking. An automated lifting and swing structure keeps the plating surface from building up deposits, which improves coating uniformity and adhesion and reduces surface defects.
- PLC automation. A PLC control system manages current, speed and tank conditions, and supports fast changeover between coating settings. Operators can run the line in automatic, semi-automatic or manual mode.
- Closed-loop, lower-waste design. Rinse and recovery loops reduce wastewater discharge and help recover zinc, supporting compliance with local environmental rules. [Confirm: waste-water treatment is the buyer’s local scope or included]
- Efficient power management. High-frequency rectification and inverter-based power management reduce energy use per ton of wire.
- Fast cooling for strength control. The quench and water-patenting section is built for stable mechanical properties on higher-carbon wire.
- Flexible coating options. Pure zinc as standard, with zinc alloy, phosphate, chromate and organic post-treatments available on request.
Electro Galvanizing vs Hot-dip Galvanizing for Steel Wire
| Factor | Electro galvanizing (this line) | Hot-dip galvanizing |
|---|---|---|
| Typical coating weight | Thin: 20–60 g/m² on this line | Heavier, often well above 100 g/m² |
| Surface finish | Bright, smooth, uniform | Duller, can be less smooth |
| Coating control | Very precise, set by current and speed | Controlled by wiping and bath conditions |
| Ductility after coating | Excellent, no molten-zinc heat exposure | Good, depends on process |
| Best for | Mesh weaving, hardware, appliance parts, packaging wire, indoor or light-exposure use | Fencing, gabions, heavy outdoor exposure |
| Energy and emissions | Electric plating, easier to control | Zinc furnace and flux/fume handling |
If your end use needs heavy zinc for many years outdoors, ask us about a hot-dip route. If you need a clean finish and tight coating control, electro galvanizing is usually the better fit.
Applications
- Wire mesh and mesh products: welded mesh, chain-link, hexagonal mesh and conveyor-belt mesh, where bright wire weaves cleanly.
- Hardware and handicrafts: hangers, display racks, decorative parts and small hardware.
- Appliance and industrial components: computer cases, washing-machine and air-conditioner parts, instrument housings.
- Building and garden: decorative frames, small fences, indoor light framing wire.
- Packaging and tying wire: lightweight sealing and binding wire.
- Fasteners and staple wire: thin, ductile coated wire for downstream forming.
Customization: what you can specify?
- Wire diameter, steel grade and number of wires
- Target output (kg/h or t/day) and annual capacity
- Online annealing: with or without
- Coating type and weight, and post-treatment (passivation, phosphate, organic)
- Take-up type and coil weight
- Plant size, utilities (gas, water, 380 V/50 Hz or your local supply) and layout
- Automation level: automatic, semi-automatic or manual
To get an accurate quotation, send us: wire material and diameter range, required coating weight, target output, available floor space, local power and gas supply, and your destination port.
Delivery, installation and after-sales support
- Lead time: typically [60–90 days] for standard configurations after drawing approval and deposit; custom lines take longer.
- Installation and commissioning: our engineers can attend your site, guide installation, commission the line and train your operators.
- Warranty: [12 months] on core equipment.
- Long-term support: technical support and spare parts supply after the warranty period.
- Shipping: standard export packing; FOB, CIF, CFR and EXW terms; nearest port Shanghai.
Frequently asked questions
1. What is a steel wire electro galvanizing line?
It is a continuous production line that cleans steel wire, deposits a thin layer of zinc on it by electrolysis, then passivates, dries and coils it. Our line handles up to 56 wires at once.
2. What wire sizes can the steel wire electro galvanizing line process?
Standard configurations process Ø0.76–3.2 mm wire in low-, medium- and high-carbon steel. Other sizes can be discussed as a custom design.
3. How thick is the zinc coating?
The standard range is 20–60 g/m², set by current density and line speed. That is roughly 3–8 µm of zinc.
4. What is the difference between electro galvanized and hot-dip galvanized wire?
Electro galvanized wire has a thinner, brighter and more uniform coating with excellent ductility. Hot-dip wire carries much more zinc and is chosen for heavy outdoor exposure. See the comparison table above.
5. Can the steel wire electro galvanizing line include annealing and pickling?
Yes. The standard flow includes degreasing, a heat treatment furnace (up to 1,100 °C, gas fired), quench, HCl pickling and rinsing. Online annealing can be included or left out depending on your wire.
6. How much does an electro galvanizing line cost?
Price depends on the number of wires, output, automation level, furnace and environmental equipment. Send your wire size, output and coating requirement and we will quote a configuration and price.
7. How long does delivery take?
Standard lines are typically [60–90 days] after drawing approval and deposit. Custom projects take longer; we confirm a schedule in the quotation.
8. Do you provide installation and training?
Yes. We can send engineers for installation, commissioning and operator training, and we provide ongoing technical support and spare parts.
9. Can the steel wire electro galvanizing line be customized to my factory?
Yes. Wire count, capacity, layout, annealing, take-up type, coating type and power supply can all be customized.




































